Loading vehicle data from NHTSA...
NHTSA recalls, safety ratings, and consumer complaints for the 2011 Mazda Mazda6.
| Overall Rating | Not Rated |
| Frontal Crash | Not Rated |
| Side Crash | Not Rated |
| Rollover |
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda CX-9 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, unless covered in "Zone A," Mazda is recalling certain 2011-2013 Mazda6, 2011-2012 CX-7, and 2011-2015 CX-9 sold, or ever registered in the states of Arizona, Arkansas, Delaware, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, West Virginia and the District of Columbia, or "Zone B." Additionally, unless covered in Zone A or Zone B, Mazda is recalling certain 2010-2013 Mazda6, 2010-2012 CX-7, and 2010-2015 CX-9 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate inflator, free of charge. The recall began November 9, 2018. Owners may contact Mazda customer service at 1-800-222-5500, Option 4. Mazda's number for this recall is 1317F.
Front Subframe has corroded and broke. There is a recall on the subframe that was repaired by dealership in 2019, but this repair did not fix the issue since it has now rusted through and broke. The repair was faulty.
Car developed a known recall issue problem, Recall 2818I. Even though Nebraska was not listed as a "salt state", it's obvious that Nebraska has similar conditions to Iowa. Attempts to contact Mazda USA corporate would not even fix the issue, citing cars age and other factors even though the damage is very specific to this particular recall.
2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.
The 2011 Mazda Mazda6 has 6 NHTSA recalls and 132 consumer complaints on file. It received an overall safety rating of Not Rated out of 5 stars in NHTSA crash testing. The high number of complaints suggests potential reliability concerns — review the complaint details above before purchasing. For the most detailed information about a specific vehicle, decode its VIN using our free decoder above.
Enter a specific VIN to get the full report — specs, recalls, safety ratings, complaints, investigations, and technical service bulletins.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North American Operations (Mazda) is recalling certain 2007-2012 CX-7, CX-9, and 2009-2012 Maza6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Mazda will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. The recall began December 3, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 1317F. Note: This recall supersedes recalls 16V356 and 17V012.
Component: STRUCTURE
Mazda North American Operations (Mazda) is recalling certain 2011-2013 Mazda6 vehicles sold, or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland,Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front cross member may corrode after exposure to road salt.
Consequence: Corrosion may weaken the mounting point for the passenger side lower control arm, unexpectedly changing the steering alignment and increasing the risk of a crash.
Remedy: Mazda will notify owners, and dealers will inspect the cross member and either install a side member and drain hose and apply wax to protect from rust, or install a drain hose and an improved front cross member, free of charge. The recall began June 13, 2019. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 2818I. Note: This recall is an expansion of Recall 18V-631.
Component: AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE
Mazda North America Operations (Mazda) is recalling certain 2009-2011 Mazda6, and 2007-2011 CX-7 and CX-9 vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Mazda will notify owners, and dealers will replace the passenger frontal air bag inflator with an alternate inflator, free of charge. The recall began on August 30, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1317F. Note: This recall supersedes recall 16V356 and all vehicles that were not remedied under that campaign are now covered by this one.
Component: FUEL SYSTEM, GASOLINE
Mazda North America Operations (Mazda) is recalling certain model year 2010-2012 Mazda6 vehicles manufactured September 14, 2009, through May 2, 2011, and equipped with 2.5L engine. In the affected vehicles, spiders may weave a web in the evaporative canister vent hose, blocking it and causing the fuel tank to have an excessive amount of negative pressure.
Consequence: Negative pressure could cause the fuel tank to crack resulting in a fuel leak, increasing the risk of a fire.
Remedy: Mazda will notify owners, and dealers will reprogram the powertrain control module and inspect and clean the canister vent line. If a web was found in the line, the fuel tank and check valve on canister vent line will be replaced. These repairs will be done free of charge. The recall began on April 30, 2014. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number associated with this campaign is 7214C.
Component: LATCHES/LOCKS/LINKAGES:DOORS:LATCH
Mazda is recalling certain model year 2009-2013 Mazda6 vehicles manufactured February 4, 2008, through August 24, 2012. The door latch mounting screws may become loose.
Consequence: If all three door latch mounting screws become excessively loose the door latch mechanism would not engage and the door might open while the vehicle is in motion increasing the risk of accident or injury.
Remedy: Mazda will notify owners, and dealers will apply a thread locking adhesive to the door screws and retorque them, free of charge. The recall began on October 29, 2013. Owners may contact Mazda at 1-800-222-5500. Mazda's recall number is 7013I.
When I took the car into my ASE mechanic shop for a normal oil change and tire rotation, they performed a general overall car inspection. They noticed that the Driver Side Rear Subframe had rusted through completely, where the coil spring is located. The passenger side was rusted, but has not yet broke through. They stated that the subframe parts should not rust through like this. They also stated that it is dangerous to drive the car in this condition. I have not notified the manufacturer as of yet, but plan to do so. There were no warning lights, but the ride did seem to be rougher than normal. The attach photos contain 2 photos of the failed driver side rear subframe and 1 photo of the good, passenger side rear subframe.
2011 Mazda6 rear subframe rot/rust, unsafe and dangerous to drive, Same situation as the front subframe that is part of a recall.
The front and back cross members underneath my Mazda6 have completely rusted out. There are numerous complaints about Mazda's "Safety Recall 2818I Expansion" not covering the back support member and also not considering Nebraska to be a Salt Belt state despite the state, and specifically Omaha using salt to treat their roads in the winter. On [XXX], my front cross member completely failed due to rust, causing my vehicle to lose control. I've taken my car to the mechanic and they confirmed the front and back cross members are completely rusted and need replacement costing $7,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2011 Mazda Mazda6. The contact stated that while her mother was driving at slow speeds in a parking area, there was an abnormally loud metallic sound coming from underneath the vehicle, and moments later, the vehicle became extremely difficult to maneuver. No warning lights were illuminated. The vehicle was towed to the dealer, who determined that the rear crossmember had detached from the vehicle due to excessive corrosion of the subframe. The contact was informed that the vehicle could not be repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 19V323000 (Structure, Suspension); the VIN was previously included, but was repaired in 2019. The contact stated that the recall repair was for the front passenger’s side lower control arm. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 150,000.
Alignment is off. Recall for my type of call for the control arm weakening and causing wheel alignment problems. Why isn't mine part of recall??
Front and rear subframe rust leading to gaping holes, outside of normal wear and tear.
The contact owns a 2011 Mazda Mazda6. The contact stated that while the vehicle was at the dealer for routine service, the vehicle was diagnosed with rust and corrosion of the sub-frame. The contact was informed that the sub-frame needed to be replaced. The vehicle was not repaired. The contact was informed of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the VIN was not included in the recall. The manufacturer was made aware of the failure. The contact was advised to contact the NTSA Hotline to report the failure. The failure mileage was approximately 100,000.
The contact owns a 2011 Mazda Mazda6. The contact stated that while reversing, the contact heard an abnormal snapping sound coming from the rear passenger’s side of the vehicle. The vehicle was stopped and inspected, where the contact observed a big spring pushing a bar into the ground on the rear passenger’s side. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 184,000.
The rear cross member / AKA (Rear Subframe) P/N GEG1-28-80X has completely rusted out. The car is no longer safe to drive per a Pennsylvania State inspection. If driven parts of the rear suspension will drop off the car creating a hazard to other motorists and the driver of the car can lose control / mobility causing a traffic accident. Picture the entire rear suspension suddenly collapsing, that is what is going to happen. The Front subframe was subject to a recall. That recall should have included the rear as it is the same material just a few feet away, subject to the same rusting issues. These subframes were not property designed to prevent rust or even withstand a little moisture, as my car has been very well maintained. When I read the online forms this is a flaw in ALL 2009- 2013 Mazda 6's and the sister car the Ford Fusion and Mercury Milan. I have opened a case with Mazda USA case #[XXX]. They are going to inspect to confirm my mechanic diagnosis. However they are currently under no obligation to repair and replace the rusted parts but they should be as this should have been replaced when the front subframe recall was performed. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
After getting the recall information about the front crossmember rusting out due to corrosion, I decided to check the rear crossmember on my car. WOW, the rear crossmember is SO much worse than the front one and I’ve read hundreds of similar stories about the exact same thing happening to other Mazda 6 sedans around these model years (2009-2013). The rear crossmember on my car, which supports the entire rear suspension is completely rusted thru in several spots and the lower end links aren’t even attached anymore because the brackets literally fell off and so now both back tires are leaning in at the top. It is very noticeable! Very unsafe to drive! I decided to park this car until a solution is reached with Mazda or the NHTSA on how to deal with this. I don’t know why the front crossmember was recalled but not the rear? There’s only 2 things that are rusted on my car, period…the front & rear crossmembers!
The contact owns a 2011 Mazda Mazda6. The contact stated that while the independent mechanic was performing an oil change on the vehicle, the independent mechanic informed the contact that the rear subframe was severely rusted with holes in the subframe. The vehicle was taken to the dealer, where it was determined that the rear subframe needed to be replaced. The vehicle was not repaired. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 19V323000 (Structure, Suspension). The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was approximately 129,000.
I'm filing a complaint as to substandard steel being used in the rear crossmember/rear subframe. Extensive corrosion has been confirmed upon a state inspection, which requires replacement at my personal cost. The front engine cradle was replaced in 2019, per a recall notice for the same extensive corrosion problem. A safety issue that needs to be addressed by Mazda.
Showing 15 of 132 complaints