2020 BMW X5 Problems & Complaints

Failure of front differential

The contact owns a 2020 BMW X5. The contact stated that the vehicle was taken to a dealer for routine maintenance and it was discovered that there was a coolant leak and that there was a failure with the front differential failure, and that the A/C unit was leaking. The leaking valve was replaced but the differential was not repaired. The contact stated that the failure was a known failure with the vehicle. The manufacturer was made aware of the failure. The failure mileage was 70,000.

Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW B58TU engines) Description of Defect: The oil pump module in the 2020 BMW X5 (G05) contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning.

Safety Hazard: Oil Pump Failure Leading to Sudden Engine Stall (BMW G05 X5) Description of Defect: The oil pump module in the 2020 BMW X5 (G05) contains internal plastic components that are prone to thermal degradation and premature failure. These plastic parts can crack or disintegrate, causing a sudden loss of oil pressure. Safety Risk: A failure of the oil pump leads to insufficient lubrication of critical engine components, which can result in a sudden and complete engine seizure while the vehicle is in motion. This causes an immediate loss of propulsion and power steering assist, significantly increasing the risk of a high-speed collision or being stranded in dangerous traffic conditions. Additional Note: This is a known mechanical defect where a critical engine component (oil pump) relies on non-durable plastic materials, creating an unreasonable safety risk for drivers and passengers due to potential catastrophic engine failure without prior warning.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (ELECTRICAL SYSTEM); however, the part to do the recall repair was not yet available. The contact stated that the vehicle failed to start. After several attempts, the vehicle started. The check control master warning light was illuminated. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 120,000.

While driving through west Los Angeles, the vehicle suddenly began emitting white smoke from the engine compartment. There were no prior warning lights, messages, or symptoms indicating a problem. The smoke quickly intensified and turned dark. Thick smoke filled the air, and the cockpit, with the smell of toxic fumes. I safely maneuvered to the shoulder and exited the vehicle with my passenger. Flames erupted from the front of the vehicle. We called 911, which dispatched the fire department. The LAFD responded, cutting open the hood in order to extinguish the fire. The vehicle was towed to a yard following the incident. The vehicle and its contents were declared a total loss.   BWM North America dispatched a technician to inspect the vehicle. After inspection, the manufacturer indicated that the starter was the source of the fire. At the time of the incident, the vehicle was subject to a safety recall related to the starter with no remedy available. The failure occurred without warning. Both occupants were exposed to heavy smoke.

I am submitting this correspondence as a formal notification of a potential safety-related defect affecting BMW vehicles equipped with the B58 Technical Update (B58TU) engine platform, most commonly model years 2019–2021. The purpose of this communication is to request immediate review under BMW’s vehicle safety defect evaluation process due to an increasing number of oil pump failures capable of causing sudden loss of engine lubrication, unexpected vehicle disablement, and occupant exposure to hazardous conditions. The original B58 engine (B58B30M0, 2015–2017) utilized a conventional mechanically robust gerotor oil pump with predominantly metallic internal construction and demonstrated strong reliability in field operation. This component, constructed from reinforced thermoplastics including PA66-GF materials, operates within a chemically aggressive and thermally cyclic environment involving continuous exposure to engine oil additives, fuel dilution, condensation, and repeated heat cycling. While acceptable under accelerated validation testing, real-world operating conditions increasingly demonstrate premature degradation consistent with polymer embrittlement and fracture. Documented owner and technician reports indicate that under cold-start conditions — particularly in sub-freezing climates — elevated oil viscosity and startup load impose increased mechanical stress on the thermoplastic carrier. Fracture of this internal component allows debris intrusion into the pump mechanism, resulting in unstable oil pressure regulation. Commonly reported precursor symptoms include: • Inability to perform electronic oil level measurement via iDrive • Erratic or oscillating oil pressure behavior • Intermittent lubrication warnings or absence of warning prior to failure • Rapid progression to bearing damage and engine seizure Given the potential for sudden vehicle disablement without adequate warning, I respectfully request BMW of North America initiate a formal inquiry

I am reporting a safety concern involving BMW vehicles equipped with the B58 Technical Update (B58TU) engine, commonly found in model years 2019–2021. These vehicles utilize a variable-displacement engine oil pump containing an internal thermoplastic adjusting component responsible for regulating oil pressure. Field failures are increasingly being reported in which this internal component fractures, resulting in sudden loss or instability of engine oil pressure. The failure frequently occurs during cold-start operation in low ambient temperatures. When the component fails, oil pressure regulation becomes erratic or is lost entirely. In many cases, drivers receive little or no actionable warning prior to engine damage or vehicle disablement. Reported precursor symptoms include inability to electronically measure engine oil level, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. Failures may rapidly progress to engine shutdown or severe mechanical damage caused by oil starvation. Loss of lubrication can cause the vehicle to become disabled without warning while driving or shortly after startup. This creates a safety hazard, particularly when vehicles become immobilized in active traffic or during winter conditions the cold is when they fail the most, where occupants may be exposed to freezing temperatures while awaiting assistance. Replacement of the oil pump requires extensive disassembly of the vehicle and repairs commonly exceed $6,000–$8,000 for just the pump, assuming the motor is unharmed. Owners are currently unable to determine whether their vehicles contain the original thermoplastic oil pump design or a later revised version utilizing metal internal components, as VIN-based parts information now identifies updated components in the car even when no replacement has occurred and the old components are actually in the car. Also, BMW has actively removed the plastic part number out of all dealer networks as well. Failures have be

I'm reporting a safety issue with BMW vehicles equipped with the B58TU engine (primarily 2019–2021 models). These vehicles use an oil pump containing an internal plastic component that regulates oil pressure. This plastic part is fracturing in the field, leading to sudden loss or instability of oil pressure. Failures commonly occur during cold starts in low temperatures. When the component fails, oil pressure becomes erratic or is lost entirely, often with little to no warning before engine damage or vehicle disablement. Warning signs, when present, include inability to measure oil level electronically, abnormal oil pressure behavior, or sudden drivetrain malfunction warnings. These can quickly progress to engine shutdown or severe engine damage due to oil starvation. My vehicle is currently experiencing all of the described oil pump-related symptoms, including inconsistent electronic oil level readings and drivetrain malfunction warnings consistent with oil pressure instability. This condition creates a serious safety risk. The vehicle can become disabled without warning while driving or shortly after startup. Oil starvation can lead to catastrophic engine failure, especially at highway speeds, where sudden engine shutdown or seizure increases the risk of a crash. Failures are particularly dangerous in winter conditions, when vehicles may become immobilized in traffic or freezing temperatures. Replacement of the pump requires major disassembly and typically costs $6,000–$8,000, assuming no engine damage. Owners cannot determine whether their vehicle has the original plastic component or a revised metal version. BMW’s VIN-based parts lookup now shows only updated components even when original plastic parts remain installed, and the original plastic part number has been removed from dealer systems. Because this defect can cause sudden vehicle disablement and potential catastrophic engine failure without adequate warning.

Please read file attached

The contact owns a 2020 BMW X5. The contact stated that while the vehicle was parked, there was fluid and lubricant on the ground underneath the vehicle. No warning lights were illuminated. The vehicle was taken to the dealer where it was diagnosed with a detached front differential shaft bearing. In addition, the contact was informed that the front differential shaft bearing caused excessive play in the propeller shaft. The contact was informed that the front differential shaft bearing needed to be replaced. The vehicle was not repaired. The contact stated that the failure was a known failure with the vehicle. The contact stated that the vehicle was serviced by the dealer seven weeks prior to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was unknown.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (Electrical System); however, the part to do the recall repair was not yet available. The dealer was contacted and confirmed that parts were not yet available for the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.

Vehicle has excessive condensation in driver headlight. Garage kept only. Problem discovered because of parking vehicle outside on driveway while the garage hosted moving boxes. This was the only time this vehicle has spent the night outside.

Was driving at normal interstate speed when I received a warning on my dashboard to pull over and turn off engine —- low engine pressure, immediately. Call a tow. I immediately pulled over, turned off my car and contacted a tow. My vehicle was towed to the BMW dealership. I received an update that my oil pump failed. It’s almost $6k to replace and then stated not sure if that’ll truly fix the problem and to change the engine $28k. I began to do research and this is a known problem. Many owners have this problem- BMW is aware and began change the plastic part to metal in the subsequent years. I received no warning that it was beginning to fail and it is a safety hazard as I was on the interstate at the time.

My 2020 BMW X5 (VIN available upon request) is subject to safety recall 25V-644 due to a fire risk. The recall has been open since November 2025. BMW has confirmed there was no available remedy for an extended period, and a BMW-coordinated service visit on January 15, 2026 could not be completed due to dealership issues. Despite repeated follow-ups with BMW North America, there has been no confirmed repair date and no consistent transportation support while the safety recall remains unresolved. I am concerned about the prolonged delay in addressing this safety issue.

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign: 25V644000 (Electrical System); however, the part to do the recall repair not available. The local dealer was contacted and confirmed that parts were not available. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the issue; however, no assistance was provided. The contact had not experienced a failure.

My steering was what I felt as an affected problem. I was subsequently stuck while out with my one year old in the cold 10/31/2024. Eventually the car started again but I had what felt like steering issues (i.e. dragging/shuttering) thereafter. I was told that there were no issues aside from the power steering which completely failed and was replaced. Not until 1 year later when I insisted that the issue continued did the dealership give me an idea of what it could be despite them knowing about the SIB the entire time. There were warning lamps that came on I'm just not sure if any of those lights were the actual undiagnosed issue pertaiing to my transfer case needing to be completely replaced. Either way the dealersihp sandbaged me and only diagnosed the transfer case replacement after I was 1 month out of warranty 11/2025 quoting me with a $10,552.19. repair cost.

The safety risk arises from inaccurate federal recall records maintained by BMW of North America. My vehicle had a safety recall for starter replacement (Recall 25V-644). This recall repair was already completed by an authorized BMW dealer, and the starter was replaced under warranty. However, BMW continues to list the recall as OPEN with “Remedy Not Available.” This creates a safety risk because inaccurate recall records may lead to improper vehicle safety status, incorrect regulatory reporting, and potential refusal of assistance if a starter-related failure or no-start condition occurs in the future. The problem has been confirmed by an authorized BMW dealer, and I have official service documentation showing that the recall repair was completed. The vehicle was inspected and repaired by BMW of Gwinnett Place. No warning lights were present after the repair. This complaint is not about a new mechanical failure, but about BMW’s failure to accurately update and close a completed safety recall, which misrepresents the vehicle’s safety status.

engine hesitates on startup and doesn't turnover. plenty of power, battery is fine. other models have been recalled, but for some reason, this model is not included. please extend this recall to include more models as the problem exists in other 2020 models not on the current recall list.

Sunroof - explosion of glass while driving down the road. No other cars or anything that would cause flying debris. I decided to file this report after reading of multiple accounts being reported.

Starter can malfunction and start fire. Unable to park in garage due to potential fire risk. BMW is aware of the problem. Care was serviced at BMW dealer and said that they have no remedy. This recall is over 15 months old.

Recall 19v-631, I am experiencing a faulty steering issue as reported in the recall. My vehicle was in production around the same time as the recall vehicles.

I was having intermittent starting issues. After a starter recall was done, things got worse. Idrive will not turn off and car wont start draining battery. Battery was replaced and car still having idrive and start issues. It would not start after being hot. I was told extended warranty is not covered and that the center console was the problem after diagnostic. They want approximately $3000 to repair. The car will not start at all and the idrive will not shut off. They said it will continue until repaired.

The contact owns a 2020 BMW X5. The contact stated while driving approximately 25 MPH, the message "Low Oil Pressure - Stop Vehicle Immediately" was displayed, and the oil warning light was illuminated. The vehicle was pulled over to the side of the road and turned off. The vehicle was towed to a dealer where it was diagnosed and determined that the oil pump was inoperable and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 81,000.

The contact owns a 2020 BMW X5. The contact stated that while stopped at a traffic light, after the light changed, the accelerator pedal was depressed and the vehicle stalled. The contact stated there was no warning light illuminated. The contact stated that the vehicle was towed to an independent mechanic. The vehicle was diagnosed, and it was determined that the starter had failed. The mechanic advised the contact that the VIN was included in NHTSA Campaign Number: 25V644000 (Electrical System). The contact was advised to have the vehicle towed to a dealer for the recall repair. The contact called a local dealer and was informed that the recall remedy was not available. The contact called the manufacturer and was informed that the remedy was not available, and there was no ETA for parts availability. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The failure mileage was approximately 75,000.

Transfer case issue which is well known across different BMW vehicles. While driving, reversing , slow parking maneuvers there is a very evident jerking sensation coming from the drivetrain. As if gears within the transfer case are slipping. Potentially dangerous while driving because the transfer case distributes power to the rear axle Issue has been confirmed by a BMW mechanic No warning lights

The contact owns a 2020 BMW X5. The contact received notification of NHTSA Campaign Number: 25V644000 (Electrical System); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while attempting to start the vehicle, the vehicle failed to immediately start. There was a timer displayed notifying the contact when to restart the vehicle; however, the vehicle failed to start. The contact's husband inspected the vehicle and noticed that the engine was running hot despite the vehicle not being driven. The vehicle was towed to the dealer. The dealer determined that the battery had failed and needed to be replaced. The dealer informed the contact that the belts and motor mounts were damaged and might need to be replaced or repaired. The dealer also informed the contact that the part was not expected until November 2025. The starter was replaced, and a software update needed to be performed. The manufacturer was made aware of the issue. The failure mileage was 73,285.

The contact owns a 2020 BMW X5. The contact stated that while stopped at a red traffic light, the vehicle lost power. The contact attempted to restart the vehicle; however, the vehicle failed to respond as intended. A dealer was contacted. The vehicle was towed to dealer where it was diagnosed and determined that the starter needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING). The vehicle was previously repaired; however, the failure persisted. The manufacturer was notified of the failure but offered no assistance. The failure mileage was 48,000.

My 2020 BMW X5 experienced starter failure after completing recall campaign 24V-576 for starter electrical overload risk. The vehicle was subject to this recall which acknowledged a defect causing electrical overload to the starter system. I completed the required software update in late 2024, approximately 4 years after the vehicle was manufactured and exposed to the acknowledged defect. Following the recall repair, the starter system failed on three separate occasions over a six-week period. The most recent failure occurred while traveling with family, creating a safety risk by nearly stranding us in a remote location. The vehicle would not start despite multiple attempts, requiring emergency roadside assistance. The failing starter component has been diagnosed and confirmed by an authorized BMW dealership service center. The dealership provided a repair estimate of approximately $3,000 for starter replacement. The component is available for inspection upon request at the dealership. Prior to complete failure, there were intermittent starting issues with the engine occasionally requiring multiple start attempts. No warning lamps or dashboard messages appeared before the failures. The vehicle has low mileage for its age, making this a premature component failure. The timeline strongly suggests the starter damage resulted from prolonged exposure to the electrical overload defect acknowledged in the recall, as the failure occurred shortly after the 4-year delayed software remedy was applied. The manufacturer has not inspected the failed component despite the clear connection to their acknowledged safety defect.

Car would randomly not start and went dead at red stop lights on occasion. Had to have the car towed to BMW dealership where they diagnosed it as a bad starter. Car only has 35,000 miles and this appears to be a know problem by BMW and BMW owners.

Suspension "clunking noise" when going slowly over bumps. Oct. 14, 2024 32,688 miles. BMW dealer replaced left front Tension Strut due to Balljoint failure/defect @ owner expense. Tire wear indicated excessive "play" in joint for some time. I had complained to BMW dealer since the car was new that it did not track straight. Car was previously aligned several times by BMW dealer but defective ball joint was not identified until i brought "clunking" noise to their attention. Balljoint failure can result in loss of control resulting in a CRASH.

I purchased a used and well serviced, one owner, BMW 2020 X5 on [XXX] from Acura of West Chester, PA. After driving the vehicle for a week the car began jerking and shuttering forward. I live in Philadelphia where space is limited and pedestrians, children included walk close to cars at stop lights and stop signs. I almost had an accident while just parking the car due of the shuttering and additionally the car unexpectedly jerked towards a pedestrian when I was stopped at a stop sign. I researched and discovered that this is a known issue concerning my year and model due to a manufacturer error when the vehicle was assembled. The incorrect oil was place into the transfer case which ultimately causes damage leading to the unsafe driving condition that I am currently experiencing. There are no warning or check engine lights to make the driver aware of the issue. Below is the direct from BMW's notice on the issue, SIB 27 02 20. To my surprise, there was never a recall to fix this issue for the make and models affected . I am asking for the NHTSA to investigate and issue are recall for repair and replacement of the transfer case that was damaged prior to consumer purchase for the models outlined in the service bulletin. BMW replaces the oil as the first level repair at the cost of the owner which seems to only be temporary. Some owners say the problem goes away and other owners the problem returns requiring replacement as the true option. I would like for BMW to recall and replace to the vehicle safe to drive. SIB 27 02 20 JERKING OR SHUDDERING FROM THE DRIVELINE (XDRIVE TRANSFER CASE ATX13 SITUATION There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages. CAUSE Unevenly worn or incorrect fitment tires are installed on the vehicle, or the factory-filled transfer case oil does not meet BMW specifications. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Fuel pump failure. Resulted in car losing speed and power and car coming to a halt. Car went into park. Had to be towed from the road but the car had to be dragged onto the flatbed due to no parking selector release accessible from the side of the road. Resulting in total destruction of the front differential resulting in $10000 repair bill.

The contact owns a 2020 BMW X5. The contact stated that after refueling the vehicle, the contact attempted to restart the vehicle; however, the vehicle failed to restart. The contact made several attempts, and after approximately an hour, the vehicle was towed to the residence. The vehicle failed to start and was towed to a local dealer. The contact stated that there were no warning lights illuminated. The dealer diagnosed the vehicle and determined that the starter motor had failed and needed to be replaced. The vehicle was not repaired. The contact researched online and related the failure to NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling). The contact called the manufacturer and asked about the recall for the starter motor and was informed that the VIN was not included in the recall. The failure mileage was approximately 30,000.

When it rains water comes into the drivers side from the roof (sun visor area), and under the dashboard. Depending on how much rain, it leaves a puddle on the floor mat, and constantly drips on the driver as I drive.

I own a 2020 BMX X5 S40i. Car was parked and turned off. When I tried to turn the car ON, the car refused to start and smoke and fire smell started coming from engine compartment. I opened the hood and could smell a burning smell. Waited for smell to disappear and tried starting the car again. Car would not start and burning smell appeared again. Got a warning on the dashboard that engine compartment was overheated and car would be ready to start after 180 seconds. Called AAA to jump start car and same behaviour was observed and car refused to start. Technician also stated that battery was completely dead. Took car to dealer and replaced main and start/ stop battery. Car still would not start. On inspection dealer observed started mechanism was shorted and needed to be replaced. After replacement, car starts fine without burning smell. Going through recall database, this issue with fire hazard from starter assembly is documented for my make, model and year but when I enter the VIN number it doesnt apply to ny vehicle VIN number. 4 year old child and me were occupants of the vehicle when burning incident happened originally.

Headlights continually fog up and puddle water in them. It takes a major effort to dry them out. Dealer says they are vented and that they will clear themselves but don't. This is a continual problem and poses a safety issue because of headlight failure.

The contact owns a 2020 BMW X5. The contact stated that upon entering the vehicle, the message that the engine had overheated, and the vehicle was disabled was displayed. No warning lights were illuminated. The vehicle was towed to the dealer, who diagnosed a failure with the starter motor. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling), but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 80,000.

The contact owns a 2020 BMW X5. The contact stated that while at a complete stop, the START/STOP feature failed to operate as designed, and the engine failed to restart while depressing the accelerator pedal. The contact stated that a "Starting Engine Possibly Shortly: System Overheated. Restarting Engine Possible After Cooling" message was displayed on the instrument panel. After the contact allowed the engine to cool down, the vehicle failed to restart with the same messages displayed. Due to the failure, the vehicle was towed to the dealer where it remained. Upon investigation, the contact discovered NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling); however, the VIN was not included in the recall. The contact also discovered and linked the failure to Technical Service Bulletin: B120424. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 73,000.

The contact owns a 2020 BMW X5. The contact stated that the vehicle failed to start. The contact stated that the message that the vehicle was overheating was displayed. There were no warning lights illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 24V576000 (Electrical System, Engine, and Engine Cooling). The vehicle was towed to the local dealer, where it was diagnosed that the failure was due to the starter. The vehicle was not repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 35,000.

A code for check engine came on and the code is say active grille shutter. I also see there is a safety issue for the same issue on other models of bmw. I'm not seeing one for X5 which needs to be added to the list.

The contact owned a 2020 BMW X5. The contact stated while the contact's mother was driving at an undisclosed speed, another vehicle attempted to make a left turn and crashed head-on into the front driver and passenger side of the vehicle. The driver's air bag did not deploy. During the impact, the driver's head hit the windshield causing it to crack. The police and paramedics arrived on the scene. The contact and the contact's mother were transported to the local medical center. The contact's mother was treated for a severe concussion and severe cuts and bruises. In addition, the contact's mother had broken glass in her hands which was removed. The contact sustained cuts and bruises. The contact's mother received additional testing because of the impact of the steering wheel on the chest, however the test results were negative. A police report was filed, however, the information was unavailable. In addition, the police officer inspected the vehicle and noticed the driver's seat belt had a lot of play, which could have contributed to the contact's mother's head injury. The vehicle was towed to the local tow yard and condemned as a total loss. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,327.

The contact owns a 2020 BMW X5. The contact stated while driving at approximately 45 MPH, the vehicle stalled. The contact stated that START/STOP warning light was illuminated. The contact attempted to restart the vehicle but was unable. The contact had the vehicle towed to a dealer who diagnosed that the starter motor had failed and needed to be replaced. The vehicle was repaired. The manufacturer was not informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling); however, the VIN was not included. The failure mileage was approximately 31,000.

The contact owns a 2020 BMW X5. The contact stated that on several occasions the vehicle failed to immediately start. Additionally, while the vehicle was idling the vehicle shut off and had to be restarted. The vehicle was taken to an independent mechanic who diagnosed that the starter was faulty and needed to be replaced. The vehicle was not yet repaired. The local dealer and manufacturer were informed of the failure, but no assistance was provided. The contact was informed that the VIN was not included in NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 60,000.

2020 BMX X5 xDrive40i experienced recall issue 24V-104. Year of vehicle is not included in recall 24V-104. I did not receive a notice of recall issue 24V-104. This recall should be extended to additional Years of this model of vehicle. Was driving in traffic on a state highway. Utilized breaks to stop the vehicle and brakes failed. Received warning notices through the cars system that aligned exactly with the errors expected to be received in Recall 24V-104. If I had been driving at a higher speed, I would not have been able to stop the vehicle and would have crashed into the vehicle in front of me at a high rate of speed, causing grave harm to myself and any individuals in the car ahead of me - and potentially any other car/individuals that were around me. The vehicle was inspected by an independent service center, which confirmed that brake failure was identical to current recall 24V-104. Auto shop only found out about the recall because they attempted to order new part and was informed that part could not be sold due to recall. Recall did not appear when VIN was searched. The problem was confirmed by the independent service center. There were no prior warnings, messages, or other systems of this problem prior to the failure and this is the first time it was experienced.

A few months ago there was a recall on my car (some problem with starter engine) and after few month I started the engine by pressing the brake pedal and pressing the start button. But the engine did not start, I saw smoke from under the hood, then I opened the hood and saw fire near the engine on the right (driver's) side. People in the parking lot helped put out the fire with a fire extinguisher while I called 911 for fire department, they came and recorded it (fire slip -[XXX]), [XXX}., Houston, Texas, 77043 (place where it happened). I have pictures and videos this incident. We were afraid that we would die in this car. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

See attached document for complaint.

On February 14, 2025, my 2020 BMW X5 unexpectedly failed to restart after engaging the Auto Start/Stop function while waiting at a traffic light. Despite multiple attempts, the vehicle would not turn back on, leaving me stranded in active traffic and creating a significant safety hazard. This failure occurred only three months after BMW applied a recall fix (software update) to address a known issue with the starter system. BMW initially issued a nationwide recall in July 2024 related to the starter function, with official letters sent to owners in September 2024. I purchased this vehicle in October 2024 and, upon learning of the recall, took it to an authorized BMW dealership in November 2024, where the recall remedy was applied (software patch). Despite this fix, the vehicle has now suffered a complete starter failure at just 50,250 miles, which is extremely premature for a modern luxury vehicle. BMW technicians at the dealership have confirmed that the starter motor itself has failed and requires full replacement. However, they claim it is unrelated to the recall, despite the failure occurring directly in line with the recall-related system. This issue is not an isolated incident—multiple BMW owners have reported similar failures following the recall fix, suggesting that the software update did not fully resolve the underlying defect. Given that the failure occurred under normal driving conditions and shortly after the recall repair, this raises serious concerns about the effectiveness of BMW’s recall remedy and the reliability of the Auto Start/Stop system. To date, BMW corporate has not yet provided a resolution, and I am seeking answers regarding whether this failure will be covered under an extended recall or goodwill repair. A premature starter failure caused by a known defect is unacceptable and presents a severe safety risk—had this occurred in a more dangerous situation, such as on a highway or at a railroad crossing, the consequences could have been

The contact owns a 2020 BMW X5. The contact stated while at a stop light, the gear shifter independently shifted into neutral. The contact stated after several attempts, the gear shifter was shifted into park. The contact stated that the gear shifter had seized in park(P). The vehicle was towed to the dealer where it was diagnosed with internal starter motor shortage. The contact was informed that the starter motor needed to be replaced. The vehicle was not repaired. The contact was informed of NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling); however, the VIN was not included in the recall. Additionally, the contact stated that the failure had occurred at night, while the four minor children were inside the vehicle. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was unknown.

The car caught on fire spontaneously when it was parked and locked. The fire started approximately 5 minutes after it was driven for 20 minutes. The fire started under the hood. There was light smoke to begin with which got worse after around 13 minutes and then flames started spewing out at the opening between the hood and the windshield. The car was fully engulfed in flames 5 minutes later with flames going as high as 2 floors. It was finally extinguished by the fire department. The car is currently with my insurance company in their tow yard.

The contact owns a 2020 BMW X5. The contact stated that the vehicle failed to start. The message "System Overheating - Restarting Engine Possible After Cooling" was displayed. The contact called AAA, who attempted to start the vehicle and shift to neutral(N), but the vehicle failed to respond as needed. The vehicle was towed to the residence with a special tow truck. The vehicle was able to be jumpstarted by AAA the following day. The vehicle was then driven to the dealer, where it was parked and turned off. The contact stated that the failure recurred at the dealer. The dealer diagnosed the vehicle and determined that the starter had failed and needed to be replaced. The contact became aware of NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling), which the contact linked to the failure; however, the dealer informed the contact that the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.

Shark fin antenna - Telematic control module malfunctioning. Seems to have a leak issue causing modules inside/under antenna to get wet from rain or car washes. This is causing an error message "SOS emergency call system malfunctioning", you will not be able to make calls under an emergency. Other issues include GPS, remote start, lane assist, adaptive cruise control etc... not working properly and potentially causing an accident on the road.

Car indicating drivetrain malfunction and BMW has a service bulletin for the described issue which is to replace the transfer case yet the dealer service center has tried to say it was the radiator blinds and it was not, now saying its spark plugs and ignition coils yet there aren’t any fault codes for it. The car has lost power while on the freeway and could be potentially dangerous since it happens while driving. Plenty of other vehicle owners reporting the same issue yet bmw not being held accountable.

Dear NHTSA, I am writing to report an issue with my vehicle, VIN: [XXX] , which appears to be related to a recall program. My dealer, BMW of Sherman Oaks #488, refuses to acknowledge the connection between the starter failure and the recall despite clear indications of this connection. I kindly request your assistance in investigating this matter and ensuring that the dealer complies with the recall requirements and provides the necessary corrective action. Thank you for your prompt attention to this issue. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2020 BMW X5. The contact stated that the message "Driver Restraint System Malfunction" was displayed. The vehicle was taken to the dealer, where it was diagnosed and determined that the driver’s side knee air bags needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was not covered under warranty. The failure mileage was approximately 39,500.

Vehicle Purchase from BMW of Devon Dear BMW Customer Relations Team, I am writing to express my deep disappointment and frustration regarding my recent experience with a Certified Pre-Owned (CPO) vehicle purchased from BMW of Devon. As a loyal BMW customer, I expected a higher standard of quality and service than what I have experienced. I purchased a 2020 BMW X5 (VIN: [XXX] in October 2023 with the confidence that it had undergone a rigorous inspection process, as advertised under your CPO program. However, after driving the vehicle for only 5,000 miles within a single year of ownership, I have been informed that the following costly repairs are required: 1. Brake pads replacement 2. RPLC both LW ctrl ar 3. Rear brake rotars 4. Front thrust arms 5. 4wa integral alignment The estimated total cost for these repairs exceeds $5,000, which is entirely unacceptable given the short duration and low mileage since the purchase. This indicates either a lack of proper inspection and servicing by BMW of Devon or a failure to disclose critical information about the vehicle’s condition at the time of sale. As a consumer, I relied on the assurances provided by the BMW CPO program, which is marketed as delivering “ultimate peace of mind” and a vehicle of premium quality. This experience has instead been stressful and costly, undermining my trust in the BMW brand. I demand that BMW of Devon and BMW of North America take full responsibility for these shortcomings by covering the cost of all necessary repairs immediately and free of charge. Anything less would not only fail to rectify this issue but also tarnish BMW’s reputation for quality and customer satisfaction. I hope this matter can be resolved promptly and amicably. Please respond within 10 days to confirm your commitment to addressing this issue. Should I not receive a satisfactory resolution, I will have no choice but to escalate this matter further, including but not limited to contact INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2020 BMW X5. The contact stated that while starting the vehicle there was a grinding sound coming from the engine compartment. While driving approximately 45 MPH, the message that the engine was overheating was displayed on the instrument panel. The contact pulled over to the side of the road and turned off the vehicle and waited for the engine to cool down. The vehicle failed to restart after the engine cooled down. The vehicle was towed to the dealer who diagnosed that the starter had failed and needed to be replaced. The dealer informed the contact of NHTSA Campaign Number: 24V576000 (Electrical System, Engine and Engine Cooling); however, the VIN was not included. The vehicle had not been repaired. The manufacturer was made aware of the failure and filed a case for the failure. The manufacturer confirmed that the VIN was not under recall. The failure mileage was 44,000.

The contact owns a 2020 BMW X5. The contact stated while attempting to start the vehicle, the vehicle failed to respond. The contact was able to start the vehicle after the sixth attempt. The vehicle was taken to an independent mechanic to be diagnosed, and the contact was informed that the engine needed to be replaced. The engine was not replaced; however, the battery was replaced. The contact related the failure to NHTSA Campaign Number: 24V576000 (ELECTRICAL SYSTEM, ENGINE AND ENGINE COOLING); however, the VIN was not included in the recall. The manufacturer was notified of the failure but offered no assistance. The failure mileage was 60,500.

There is a known recall on this car for engine/starter. It is a hazard and should be repaired. On 10/23 we scheduled and took the car to BMW of NW Arkansas. They refused to complete the recall on the starter without us paying $189.00 for a vehicle diagnostic and I am sure that would have resulted in more fees. A recall should be completed free of charge as it directly relates to a safety issue. Another issue on the vehicle that I am not sure if it is a recall items is the GPS antenna allows water to intrude and thereby the GPS/safety location services to fail. It is a complained about issue online from BMW owners. BMW will not replace or repair this faulty item either. "A recall is issued when a manufacturer or NHTSA determines that a vehicle, equipment, car seat, or tire creates an unreasonable safety risk or fails to meet minimum safety standards." BWM refuses to adhere to this standard and is placing my family at risk by failing to repair without me paying for it. They should be forced to complete this at no cost.

[XXX] my engine started stopped working even several times of trying the SUV didn’t star I took it to BMW Braman Miami center to fix the problem I was charged $3,997.18 since it wasn’t a recap of the engine starter yet I called my advisor Nasser Darwich for the recall reimburse after I get the letter from BMW USA & he told me it was no reimbursement INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Due to a small coffee spill srs light for front and back were triggered, with the potential of having air bags deployed, this is a defect that needs to be addressed. There was a class acton lawsuit that has since been concluded, but how about for new owners of old vehicles. This should be a safety concern.

The contact owns a 2020 BMW X5. The contact stated while driving at an undisclosed speed, the contact became aware that the engine was overheating. There was no warning light illuminated. The vehicle was taken to the dealer where it was diagnosed and determined that the starter had failed and caused the battery to fail. The contact was informed that the starter and battery needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 64,671.

Passenger Seat Belt Malfunction indicator on stating the system has a malfunction. Passenger safety systems are reduced in the stated malfunction. It has not been inspected by the dealer or service center. There were no known issues prior to the vehicle indicator stating the system malfunctioned.

Starter malfunction caused engine to shut down in the middle . Message on screen indicated that the engine overheated and shut down was to prevent further damage. Drivetrain messages also appeared indicating that vehicle was ok to drive, but unfortunately wouldn't start/drive. Wouldn't shift to Neutral for towing. BMW dealer inspected vehicle, then replaced batteries and faulty starter. Event happened PRIOR to receiving notice re safety recall campaign no. 24V-576 for the engine starter remedy. Event happened without warning and about a mile from home , causing vehicle to stop in moving traffic on a very busy, 6 lane road. Policy were dispatched to help with traffic control and safety. Vehicle was inspected by and serviced by BMW dealer.

The contact owned a 2020 BMW X5. The contact stated that she parked the vehicle in her garage. No warning light was illuminated. The contact entered her home and 15 minutes later, a neighbor knocked on the door, alerting her that the garage had caught fire. When the contact opened the garage door, she saw flames. The contact called 911 and evacuated her family. There were no injuries sustained. The police and fire departments arrived on the scene, and the firefighters extinguished the fire. The fire destroyed all three vehicles in the garage and engulfed the residence. Police and fire department reports were filed. The vehicle was towed to the tow yard. The insurance company deemed the vehicle totaled. The contact later became aware of NHTSA Campaign Number: 24V576000 (Electrical System, Engine And Engine Cooling) associated with the VIN. The manufacturer was not made aware of the failure. The failure mileage was unknown.

The contact owns a 2020 BMW X5. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated on the instrument panel. The vehicle was taken to the dealer, who diagnosed a failure with the active grill shutter. The vehicle was not repaired. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 61,000.

How does a known manufacturing defect ( or the factory-filled transfer case oil does not meet BMW specifications.) Not become a safety concern. The wheels have intermittent power from the transfer case. My car showed the concern at 55k miles and the warranty company made me go through another 12 months of the shuddering issue before replacing. When moving from winter to all season tire it became more noticeable. When setting off from a slope my power loss was even greater causing the front wheels to slip from the shuddering power train. This possess a greater risk on loose paving.

The front passenger door remained open as I was pulling out of my garage with my kid sitting in the front passenger seat. I thought he didn't close the door, but he was unable to close it. I got out of the car and it turns out the door wouldn't latch. There was no warning to the failure of the soft closing door mechanism. Just an alert that door is open. I had to drive it to the dealership the next day with rope securing the door to the pillar and the rear passenger door.

My 2020 BMW X5 is having the same issues as SIB651222 based on the extensive troubleshooting that I have done with the telematics system. ALL of the exact symptoms can be found in this YouTube video for an X7: [XXX] . INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I was parking the car in a parking lot. I had my foot completely off of the gas pedal while allowing the car to roll forward into a parking spot. The car suddenly accelerates and I could not slam on the brakes fast enough to prevent damage. This was the 3rd time this type of incident occurred in this car.

cHECK ENGINE LIGHT IS ON AND BASED ON THE CODE THERE IS A PROBLEM WITH THE ACTIVE GRILL SHUTTERS. i DID SOME RESEARCH AND SEEMS THIS IS A COMMON PROBLEM WHERE THE ACTUATOR MOTOR MAY BE THE PROBLEM

The front headlight enclosure repeatedly fogs because moisture gets inside. It has just happened again to us. This has been widely reported by BMW owners and is a significant safety issue that BMW has not addressed. In the interest of public safety BMW should recall and replace whatever defective parts cause the problem.

The contact owns a 2020 BMW X5. The contact stated that upon starting the vehicle, the check engine warning illuminated on the instrument panel. The vehicle was taken to the dealer, who diagnosed a failure with the active air flap controller. The vehicle was not repaired. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 45,000.

Rear restraint system malfunction. BMW states it’s a faulty airbag that is not under warranty. Car has never been in an accident and only 4 years old so there should not have been any issues. It is a safety issue for passengers.

I was driving in the rain and I experienced an issue with a vehicle’s automatic safety systems that are designed to aid you from crashing and it would have been the proximate cause of my fatal accident had I not realized what was happening and stopped the system’s actions. The system kicked in when I touched the rumble strip with my front left tire but I brought it back before the system could because it detected the event and created a countering event to correct my mistake, hence begins the issue. When the car veered right it didn’t need to so I had to counter that movement to keep from hitting the car next to me. The car then detected this and created another event that I again corrected before the system could. This created a situation now where the systems working together were creating events to correct events it didn’t need to do because the systems when working together now had a response time to real world events slower than mine and it couldn’t stop itself from doing this solely due to a lack of processing power. In less than 2 seconds I went from driving straight to fighting a car that put me into a horizontal “death wobble” that would have caused my car to spin either clockwise or counterclockwise at some point had I panicked and slammed on the brakes, which is what most people would have done in this situation, but I knew better. I realized what was happening immediately and I stopped it by simply keeping the steering wheel centered straight ahead forcefully until the safety systems caught up and cleared all the events. I am giving you the short version because the system in the first 1-2 seconds made, created, and stacked at least 5 of these events as I fought to correct them until the vehicle’s body roll and “death wobble” stopped and I was able to drive straight again. The wet roadways and rain only made it worse. This is a huge problem and may cause so many fatal accidents that I can’t even imagine, as I a retired policer this

The contact owns a 2020 BMW X5. The contact stated that the PUSH to START button was inoperable. The contact stated no warning light was illuminated. The contact took the vehicle to the local dealer, where it was diagnosed with needing the control sensor for the start button to be replaced. The vehicle was repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 40,800.

I have received two malfunction alerts two months apart for both driver and passenger airbags. The first dealership reset the fault codes and the second different dealership found 4 faults and reset it as well. I learned from the second dealership that the airbag sensors sit below the cup holders, secured by a screw in each cup on the bottom base of the housing. They removed the rubber bottom portion of the cup holder and noticed there was liquid reside and the screw appeared rusted. They believe the water may have leaked through the screw and ruined the airbag sensors. If this was true, they mentioned the airbags would not work properly and I would be responsible to pay for the work performed to correct the issue since they consider this a outside influence and not covered by my warranty. I mentioned that this a a huge safety concern, a terrible design flaw, and no where in the owners manual does it warn owners of the potential safety concerns of using cup holders that seat above the airbag sensors. I contacted BMW public relations, filed a complaint, and they have heard of this complaint before and advised different safety teams would see my compliant and wait for a callback.

BMW front cup holders have hole in bottom and it allows condensation/liquid to migrate through bottom to air bag sensor located directly underneath cup holders. Consumers are at risk of air bags going off unintentionally and/or not going off at all. Sensor should not be directly under a cup holder and/or the cup holder should not have a hole directly above safety sensor. BMW design defect. Consumers are having to pay out of pocket for sensor to be replaced as it is not covered under warranty. Additionally, there is a pending class action lawsuit that has been filed and documentation of this being a problem over several BMW models is well documented in forums, etc. on the internet.

WHILE PARKING THE VEHICLE IN A HEAD-ON PARKING SPOT, THE CAR SUDDENLY ACCELERATED WITHOUT WARNING AND HIT A WALL. THE CAR THEN WENT INTO REVERSE AND SPED UP RAPIDLY UNTIL IT HIT A CONCRETE PATIO ON THE OTHER SIDE OF THE PARKING LOT. THE BRAKE PEDAL WAS DEPRESSED WITH SUBSTANTIAL FORCE THE ENTIRE TIME THE VEHICLE WAS MOVING BUT THE VEHICLE WOULD NOT STOP MOVING. THE BRAKES DID NOT ENGAGE. I DO NOT RECALL HOW THE CAR WENT FROM DRIVE TO REVERSE. FORTUNATELY, THERE WERE NO PEOPLE OR CARS IN THE PARKING LOT AT THE TIME OF THE INCIDENT. THE AUTO BODY SHOP THAT CURRENTLY HAS POSSESSION OF THE VEHICLE COULD NOT FIND ANYTHING WRONG WITH THE COMPUTER/ELECTRICAL SYSTEMS IN THE VEHICLE NOR WERE THEY ABLE TO RECREATE THE INCIDENT. I DO NOT KNOW HOW THOROUGH THEY LOOKED FOR PROBLEMS. BMW HAS BEEN NOTIFIED AND HOPEFULLY THEY WILL SEND A CREW TO INVESTIGATE. THE CAR IS CURRENTLY AT THE AUTO BODY SHOP BUT MY INSURANCE GOMPANY, GEICO, WILL HAVE THE CAR TOWED TO ONE OF THEIR FACILITIES IN A COUPLE OF DAYS. THE CAR HAS BEEN DEEMED A TOTAL LOSS DUE TO ALL OF THE DAMAGE. I HAVE BEEN HAVING ELECTRONICS ISSUES WITH THE CAR SINCE PURCHASE IN JUNE 2020, HOWEVER, THEY HAVE BEEN RELATED TO THE ENTERTAINMENT AND COMMUNICATION SYSTEMS. IN HINDSIGHT, I REALIZE THAT I HAD TWO OTHER INSTANCES IN THE PAST WITH SUDDEN ACCELERATION WITH THIS CAR. I THOUGHT NOTHING OF IT AT THE TIME BUT THEY MAY BE RELATED TO THIS LATEST INCIDENT.

squeaking and grinding in steering column, overheated steering column to the touch. Took to local BMW and was informed it was an issue with steering rack (after two visits there) and part has to be ordered and replaced.

BMW states the X5 is equipped brake pad sensor and will notice driver when is needed to be replace. it doesn't work and become a safety concern. We have this X5 for about 2 years and start to hear noise when apply the brake. When the situation happens, we have never seem any alert from the car. Which our previous 2017 X5 and 440 GC provides such function. We found an opportunity to sent the vehicle to server center and asked to check what's wrong. Then, we are told that the front left brake pad against the rotor surface and has been metal to metal. We are told, if this is getting worse, the vehicle may not be able to stop safely. This is a safety issue of the 2020 X5. if I didn't ask my wife to go check the car, she might be in a car accident since she can't stop the car. Money thing is details. I provides this in order to match the file I uploaded later. We are provided detailed inspection report and asked to pay $1000+ to fix the issue (X5 Quo.pdf) Service center provides detailed report for the status of the car. (report.pdf) in the end, we were able to negotiate to buy an extension warranty($700) to cover the cost. (payment.pdf)

Grievance/Complaint for 2020 X5 BMW Firer December 9, 2021 (49 days Owner) I was on my way to work, and I stopped at the local Bank of America drive through. While on my way, I received two (2) malfunction message saying the same thing, “ Scam Likely 1-470-781-9727; (Check Control) Vehicle key missing, Close message; Vehicle key not available or malfunctioning. Drive-ready mode cannot be started. See Driver’s Manual for further information.” (This was the message/malfunction.) I took a picture and call my salesperson, Mr. Preston at BMW of Gwinnett Place and informed him that the key was in the cup, so I tried to place it on the dashboard. I did not understand why I received a malfunction message the key missing because the car would not go anywhere without a key, however, he asked me to send the picture to him and I did. As I was getting out my X5, I began to have anxiety and became traumatized (praying, crying, yelling etc.) at this point, thinking my X5 is going to catch a fire and blow up the bank. I went into the Bank to alert them of the X5 smoking so that they can evacuate if needed. I went back to my X5 to gather as much as I could of my Christmas gifts and other Items quickly. At that time another lady was standing on the side walk and asked if she could help me removed the items from my X5.I was hysterical, and my hand was bleeding from grabbing items out the X5. My safety and others was at risk. The X5 could have been in my garage on firer and my house and family could have died and lost everything; The seat belt could have locked with me in it and I could have died. The bank ATM drive through could have blown up and all the customers could have been injured.BMW of North America insisted that I fill on my insurance because the the engineers did an observation investigation and did not see any fault of manufacture or electrical issue.The vehicle is now under the investigation of my insurance and I have not been notified of the cause at this time.

Purchased the car Feb 2020. Over 6 months ago, back seat belts (middle and left side) stopped working. Seat belt will not click. Brand new car with nonfunctioning seat belts. Been trying to get hold of the dealer to fix and did not get anywhere. After months of hassle, they ordered the seat belts to be replaced. After dropping off the car, I get an email asking me to approve the fix for a cost of $1,100. Want to report malfunctioning unsafe car with nonworking seat belts (brand new car, a little over 1 year old) and a dealer that want to charge me for their malfunctioning seat belts. anyone that get in the car in the back is not safe. cannot use the car due to safety issues.

My 2020 X5 is equipped with Rear Cross Traffic Warning however it does not warn when traffic is crossing. The car will be in reverse, i can be very close to either a car or a person and there are no audible or visual warnings until the object stops moving or is within inches of the vehicle. I have taken it to my dealership several times however they are stating its in full working function even though it does not do what BMW advertises how that system should work. This is both very dangerous and false advertising by BMW! I have videos to prove this claim however the upload section doesn't allow videos.

Backing out of my garage to a street with a 25 mph speed limit, the vehicle is supposed to alert the driver with a warning sound and or brake if a vehicle is crossing behind the vehicle. This feature has never worked and the dealer can't find any problem. This condition has been report on several internet websites with no resolution.

Automatic braking system. Traveling about 50 MPH the automatic brake activated, there was nothing even close to my vehicle, my passenger's head was jerked forward. I had the vehicle in for computer problems about two weeks ago, concerning the radio and dash board displays, not knowing about the automatic braking problem at that time, ( this is the second incident involving the automatic brake, first time I didn't think too much about it since I had just purchased the vehicle I thought maybe a new car bug ). I was told that there was no fix for the problems I took it in for , and that Germany was notified and they had no solution, when a fix was found I would be notified. Now I'm now realizing more is affected by the faulty computer system then I first thought. My main concern is getting rear ended on the highway which I travel quite often. This incident occurred Saturday evening, today I'm contacting the dealership, we will see what happens with a more serious problem.

THE AUTO-DIMMING FEATURE OF THE DIGITAL INSTRUMENT PANEL ON 2020 BMW X5 MODELS IS POORLY IMPLEMENTED, AND UNDER VARIABLE LIGHTING CONDITIONS (CLOUDY, SNOWY, SUNRISE, SUNSET), IT DIMS AT INAPPROPRIATE TIMES, SUCH AS WHEN DRIVING TOWARD THE SUN AT SUNRISE OR SUNSET. THIS MAKES THE DISPLAY EXTREMELY DIFFICULT TO READ AND UNSAFE. THE AUTO-DIMMING FEATURE FOR THE INSTRUMENT PANEL IS ONLY APPROPRIATE UNDER NIGHT-DRIVING CONDITIONS.

MY SAMSUNG GALAXY S9 PHONE SEEMS INCOMPATIBLE WITH MY X5. ABOUT EVERY 30 MINUTES THE NAV DISPLAY AND HALF THE INSTRUMENT PANEL BLACK OUT FOR ABOUT 10 SECONDS THEN RESTARTS. THIS OCCURS ON THE HIGHWAY AND IN THE CITY.

AIR CONDITIONING QUIT WORKING ON DAY 2 OF OWNERSHIP. DEALER SAYS THE COMPRESSOR NEEDS TO BE REPLACED AND THERE IS A LEAD TIME BETWEEN 2 WEEKS AND 2 MONTHS. AFTER PURCHASING A CAR THAT COST ABOUT $125,000 AND DRIVING IT ONE TIME, IT HAD TO BE SENT TO THE SHOP. SINCE IT IS SO HOT WHERE I LIVE, DRIVING THE CAR IS OUT OF THE QUESTION. BMW DID GIVE ME A LOANER CAR, BUT THE VALUE OF THE LOANER IS ABOUT 45% OF THE CAR I PURCHASED. *TR

NAVIGATION DISPLAY AND RIGHT SIDE OF INSTRUMENT PANEL GO BLANK INTERMITTENTLY AND THEN RESET AND COME BACK ON AFTER ABOUT 10 SECONDS. DISPLAY GOES OFF DURING PERIODS OF DRIVING AND OR STATIONARY WITH VEHICLE ENGINE RUNNING. OCCURS DURING TIMES AT HIGHWAY SPEEDS AND CITY DRIVING. *TR

MY VEHICLE HAS NOT BEEN INVOLVED IN ANY ACCIDENTS AS A FUNCTION OF THIS DESIGN FLAW. THE FOLLOWING OCCURS WHEN VEHICLE IS IN MOTION OR STATIONARY: DURING DAYTIME DRIVING, WHEN HEADLIGHTS ARE NOT TURNED ON, THE DIGITAL INSTRUMENT PANEL AND DIGITAL CONTROL PANEL DIM UNDESIRABLY, MAKING THEM DIFFICULT TO READ AND CREATING UNSAFE DRIVING CONDITIONS. THIS IS UNDESIRABLE BEHAVIOR IS MOST PREVALENT ON CLOUDY DAYS AND AT SUNRISE AND SUNSET. THE DIMMING NEEDS TO BE INACTIVE IF HEADLIGHTS ARE OFF. IF HEADLIGHTS ARE ON, IT NEEDS TO BE INACTIVE IF BRIGHT LIGHT IS DETECTED THROUGH WINDSHIELD (SUNRISE, SUNSET) -OR- IF BRIGHT LIGHT IS DETECTED INSIDE THE CABIN.